Comments on: How to Install Solar Panels : Mounting Rails on Roof for Solar Panels

By: berakdata

berakdata — Tue, 15 Jun 2010 23:37:41 +0000

FANTASTIC!

By: zebart00

zebart00 — Tue, 15 Jun 2010 22:45:14 +0000

it’d be nice if these videos were in chronological order….

By: 123kkambiz

123kkambiz — Tue, 15 Jun 2010 21:54:06 +0000

Are you sure , you are working with the codes, No way it is accepted to mount the solar ray without proper insulation of roofing. Please dont make such unprofesional installation procedure in UT. with that single screw which you mounted rail on the roof , it cant stand the wind spped of 100 miles per hour. secondly you should find the stud first nt just screw over the shingle.

By: carlt0nsharple

carlt0nsharple — Tue, 15 Jun 2010 20:57:57 +0000

PM me for solar deals

By: InspireImages

InspireImages — Tue, 15 Jun 2010 20:08:44 +0000

Isn’t that going to leak?

By: hermancando

hermancando — Tue, 15 Jun 2010 19:10:35 +0000

i dont think you should drill a hole through the metal on the shingle and what did you seal hole with and the one block was already cracked -does the home-owner know bout this video i would be pissed are you even a license contractor you scare me dude-

By: larlev40

larlev40 — Tue, 15 Jun 2010 19:05:51 +0000

This is called “expert village”. This is exactly why a certified installer should do an install.
The internet has some really bad information out there….homeowners do not copy this method…you will be sorry.

By: nalepap

nalepap — Tue, 15 Jun 2010 18:46:06 +0000

this is a joke!!

By: solarforfuture

solarforfuture — Tue, 15 Jun 2010 17:54:08 +0000

Lighten up folks. mount some panels on your rat shack and get some lights on… its easy to do with the stuff on hand… yes we all want pro contractors to do all our work for us… nothing $ 100 bucks an hour wont cure. But it is an easy DIY as we see here… dont be scared! EMPOWER yourself for the future…
Its true though if you have strong wind you can use 2 bolts… or more. new wood.. sealer thats ok too.. ground rack, motor home.. fine by me.
See?
R
R

By: hazeyfla

hazeyfla — Tue, 15 Jun 2010 17:15:24 +0000

I would fail every inspection if I did an install in this manner. Don’t go cheap when you go green!

By: juggernautxtr

juggernautxtr — Tue, 15 Jun 2010 16:25:12 +0000

@solarforfuture
so skimping out on a 4 dollar water tight box is a good idea? using mc (metallic cable) outside is a good idea when he could use seal tite or sjo cord which is cheaper than mc ? sorry but everything i have seen this guy do is hack job crap.

By: juggernautxtr

juggernautxtr — Tue, 15 Jun 2010 16:24:28 +0000

@larlev40
or at least find an electrician that will do the job for less and do it correctly.
DON”T DO WHAT THIS GUY IS DOING PLEASE!!!!!

By: solarforfuture

solarforfuture — Tue, 15 Jun 2010 15:59:19 +0000

so sorry to frighten you all.. I should have shown working to code… but really, here we are with 30 volts at 4 amps on the roof, even at dead short there is no danger! any wire is ok. you scared experts could not hurt yourselves with this set up if you tried. Getting off the grid is not rocket science. No inspector on this job but my 100 installs here in SoCal ALWAYS pass 3 state inspections.. $40,000 buys a lot of safety hardware… you may not need it all ??
See?
Rge

By: juggernautxtr

juggernautxtr — Tue, 15 Jun 2010 15:36:34 +0000

@solarforfuture
dude your are ignorant it only takes half a mili-amp to kill you.
I have been an electrician for 15 yrs and no one that takes pride in their work does crap like this.
you are one of the reasons why i hate working in electrical cause scum like you ruin it for guys like me doing it right the first time. then I have to turn around a fix shit work like this which ends up costing people more cause it takes longer to fix the crap work than doing it right in the first place.